This documentation is for Dovecot v2.x, see wiki1 for v1.x documentation.
Differences between revisions 13 and 14
Revision 13 as of 2010-07-12 14:45:44
Size: 4966
Editor: TimoSirainen
Revision 14 as of 2011-01-24 20:22:30
Size: 4981
Editor: TimoSirainen
Comment: use non-existing example domain, exists!
Deletions are marked like this. Additions are marked like this.
Line 23: Line 23:
# telnet 143 # telnet 143
Line 25: Line 25:
Connected to Connected to
Line 46: Line 46:
# telnet 143 # telnet 143
Line 61: Line 61:
# openssl s_client -connect # openssl s_client -connect
Line 66: Line 66:
# openssl s_client -connect -starttls imap # openssl s_client -connect -starttls imap

For testing POP3 installation, see TestPop3Installation.

Check that it's running

First check with ps that dovecot process is actually running. If it's not, you had an error in dovecot.conf and the error message was written to log. Go back to RunningDovecot and Logging if you can't find it.

Check that it's listening

Next check that Dovecot is listening for connections:

# telnet localhost 143
Connected to localhost.
Escape character is '^]'.

If you got "connection refused", check that imap is included in protocols setting in dovecot.conf. Also check that listen setting is *.

Next check that it also works from remote host:

# telnet 143
Connected to
Escape character is '^]'.

If that didn't work, check all possible firewalls in between, and check that listen setting is * in dovecot.conf.

If you have only imaps enabled, see "remote login" section below for how to test using openssl s_client.

Check that it's allowing logins

# telnet localhost 143
a login username password

Replace the username and password with the ones you added to passwd.dovecot in BasicConfiguration. Note that all IMAP commands begin with a tag, which is basically any string you want, but it must be there. So don't leave out the "a" in the above example.

You should get an "a OK Logged in." reply. If you get "Authentication failed" error, set auth_verbose = yes and auth_debug = yes in dovecot.conf, restart Dovecot and try again. The log file should now show enough information to help you fix the problem.

Check that it's allowing remote logins

You'll need to try this from another computer, since all local IPs are treated as secure:

# telnet 143
a login username password

If the connection is hanging instead of giving * Dovecot ready, you have a firewall that's preventing the connections.

Otherwise, the only difference here compared to step above is that you might get:

* BAD [ALERT] Plaintext authentication is disabled, but your client sent password in plaintext anyway. If anyone was listening, the password was exposed.
a NO Plaintext authentication disabled.

If this is the case, you didn't set disable_plaintext_auth = no. You could alternatively use OpenSSL to test that the server works with SSL:

  • Test using imaps port (assuming you haven't disabled imaps port):
    # openssl s_client -connect
    * OK Dovecot ready.
  • Test using imap port and STARTTLS command (works also with imap port):
    # openssl s_client -connect -starttls imap
    * OK Dovecot ready.

Check that it finds INBOX

After logging in, check that the INBOX is found:

b select inbox
* FLAGS (\Answered \Flagged \Deleted \Seen \Draft)
* OK [PERMANENTFLAGS (\Answered \Flagged \Deleted \Seen \Draft \*)] Flags permitted.
* OK [UIDVALIDITY 1106186941] UIDs valid
* OK [UIDNEXT 2] Predicted next UID
b OK [READ-WRITE] Select completed.

It should contain the mail that you sent to yourself in FindMailLocation step.

If anything goes wrong, set mail_debug = yes and try again. The log file should now contain debugging information of where Dovecot is trying to find the mails. Fix mail_location setting and try again.

Check that it finds other mailboxes

If you already have other mailboxes created, you can check that Dovecot finds them:

c list "" *
* LIST (\NoInferiors) "/" "test"
* LIST (\NoInferiors) "/" "INBOX"
c OK List completed.

If they weren't found, set mail_debug = yes and look at the debugging information. Fix mail_location setting and try again.

Check that real mail clients work

Since mail clients can be configured in various ways, please check first if the problem is with Dovecot configuration or with the client's configuration. You can rule out it being Dovecot's problem with the "telnet" methods described above.

If you can't log in,

  • Make sure SSL/TLS settings are correct.
  • Make sure the client uses plaintext authentication method, unless you've specifically configured Dovecot to accept others.

If you can see only INBOX,

  • Clear out any "IMAP namespace prefix" or similar settings from clients.
  • Check if client is configured to show only "subscribed mailboxes". If so, you'll have to subscribe to the mailboxes you wish to see. You can see a list of subscribed mailboxes with:

    d lsub "" *
    * LSUB () "/" "INBOX"
    d OK Lsub completed.

Most IMAP clients have been tested with Dovecot and they work.

None: TestInstallation (last edited 2020-01-02 18:15:18 by 67)