This documentation is for Dovecot v2.x, see wiki1 for v1.x documentation.
Differences between revisions 20 and 21
Revision 20 as of 2013-09-07 20:25:59
Size: 3099
Editor: d133218
Revision 21 as of 2014-01-22 14:35:46
Size: 2791
Editor: TimoSirainen
Deletions are marked like this. Additions are marked like this.
Line 22: Line 22:

# Outlook Express and Windows Mail works only with LOGIN mechanism, not the standard PLAIN:
auth_mechanisms = plain login
Line 63: Line 66:
=== Remark ===
If Outlook Express (and/or Windows Mail) doesn't seem to login, even though you checked "My server requires authentication" in it's configuration, then verify that the "mechanisms" line contains "login" in addition to "plain". "plain" is the default, and most clients can work with it, but Outlook Express needs the "login" mechanism. Also see:


Postfix and Dovecot SASL

Since version 2.3, Postfix supports SMTP AUTH through Dovecot SASL as introduced in the Dovecot 1.0 series. If using Postfix obtained from a binary (such as a .rpm or .deb file), you can check if Postfix was compiled with support for Dovecot SASL by running the command:

postconf -a

Once you have verified that your installation of Postfix supports Dovecot SASL, it's very simple to configure:

Example conf.d/10-master.conf excerpt

service auth {
  unix_listener /var/spool/postfix/private/auth {
    mode = 0660
    # Assuming the default Postfix user and group
    user = postfix
    group = postfix        

# Outlook Express and Windows Mail works only with LOGIN mechanism, not the standard PLAIN:
auth_mechanisms = plain login

Example Postfix excerpt

smtpd_sasl_type = dovecot

# Can be an absolute path, or relative to $queue_directory
# Debian/Ubuntu users: Postfix is setup by default to run chrooted, so it is best to leave it as-is below
smtpd_sasl_path = private/auth

# On Debian Wheezy path must be relative and queue_directory defined
#queue_directory = /var/spool/postfix

# and the common settings to enable SASL:
smtpd_sasl_auth_enable = yes
# With Postfix version before 2.10, use smtpd_recipient_restrictions
smtpd_relay_restrictions = permit_mynetworks, permit_sasl_authenticated, reject_unauth_destination

Using SASL with Postfix submission port

When Dovecot is used as the authentication backend for Postfix it is good practice to use a dedicated submission port for the MUAs (TCP 587). Not only can you specify individual parameters in overriding the global ones but you will not run into internet mail rejection while the Dovecot Auth Mechanism is unavailable. In this example Postfix is configured to accept TLS encrypted sessions only, along with several other sanity checks:

  • Verification of alias ownership via Login Maps
  • Domainname and recipient plausibility

submission inet n - - - - smtpd
  -o smtpd_tls_security_level=encrypt
  -o smtpd_sasl_auth_enable=yes
  -o smtpd_sasl_type=dovecot
  -o smtpd_sasl_path=private/auth
  -o smtpd_sasl_security_options=noanonymous
  -o smtpd_sasl_local_domain=$myhostname
  -o smtpd_client_restrictions=permit_sasl_authenticated,reject
  -o smtpd_sender_login_maps=hash:/etc/postfix/virtual
  -o smtpd_sender_restrictions=reject_sender_login_mismatch
  -o smtpd_recipient_restrictions=reject_non_fqdn_recipient,reject_unknown_recipient_domain,permit_sasl_authenticated,reject

See also:

None: HowTo/PostfixAndDovecotSASL (last edited 2014-12-30 23:19:11 by pool-98-111-147-67)